Miles Industries 739IRP Owner's Manual

LEGEND4003901-06©2015, Miles Industries Ltd.DV Gas Insert739JLN/P (Logs) & 739IRN/P (Rocks)Installation & Owner’s ManualThis manual contains i

Remote Control OperationSETTING THE TIMESETTING ºC/24-HOUR OR ºF/12-HOUR CLOCKMODES OF OPERATIONNOTE: Manual mode can also be reached by pressing eith

Remote Control OperationSETTING THE ON / OFF TEMPERATURES• Briefl y press SET button to scroll to TEMP (sun) mode. Hold the SET button

SETTING PROGRAM TIMERS• You can program two periods of time between 12:00 am and 11:50 pm in each 24-hour cycle.• The Programs P1 and P2 must be set

OptionsRequired Kits*VentingSee Approved Venting Components section.Inner Fronts (choose one)741—Contemporary Front with Barrier Screen 4003360742—Tra

Lighting InstructionsWARNING: If you do not follow these instructions exactlyD¿UHRUH[SORVLRQPD\UHVXOWFDXVLQJSURSHUW\GDPDJHSHUVRQDOLQMXU\

XXRatingsModel NG LPGGas Natural PropaneAltitude (Ft.)* 0-4,500 feet*Input Maximum (Btu/h) 26,000 24,000Input Minimum (Btu/h) 6,500 13,000Manifold Pre

OverviewThis appliance may ONLY be installed in an existing unaltered, functioning solid-fuel burning fi replace with a working fl ue and constructed of

28-5/8” (727 mm)19-1/2” (495 mm)12 - 14” (305 - 357 mm)Varies with outer trim options9-3/8 - 11-3/8” (238 - 289 mm) Varies with outer trim options20”

ABDo not putfurniture orobjects within36” (914 mm) of the front ofappliance9” (229 mm)Sidewall ClearancesMinimum distance from side of appliance (lin

Terminal CapFlashing2 x 3” fl ex liners—see Venting Table for length allowedTypical Vent InstallationSee the Approved Venting Components list on page 3

Safety Precautions ...3Safety and Your Fireplace ...4Owner’s Informat

Installation PlanningExisting Fireplace PreparationA few points must be considered before inserting the 739 into an existing fi replace cavity. General

Unpack the applianceBeware of sharp edges! Wear gloves!1. Unpack the appliance.2. Unpack any loose items from around the appliance and check against

electricaloutletfancavityInstallationRemove WindowThe window is held in place by four spring-loaded bolts, two at the top and two at the bottom. 1. T

Connect VentingIMPORTANT: This appliance’s venting system is room sealed and therefore, does not require room air to be used in the combustion process

Supply pressuretest tappingManifold pressuretest tappingConnect Gas SupplyThe gas supply inlet connection is a 3/8” NPT female connector and is locate

Rotate anchor up and insert panelPosition of panel in relation to burner plateEdge of burner plateSide panels should be parallel to edge of burner pla

Install Ceramic Logs (739JL)Unpack the ceramic logs very carefully to avoid damaging the fragile material. Install the logs as shown below. Please not

6. Place the lower end of the center right log onto the pin on the front right log. Rest the narrow end in the notch into the rear log.7. Pour some

TopBottom1. Install the Front Support Platform in the fi rebox carefully sliding it down between the burner and the front bottom edge for the fi rebox

4. The underside of each ceramic rock is identifi ed by a number and a specifi c protruding positioning triangle.Install the six rocks from left to rig

3Safety Precautions!Children and adults should be ALERTED to the hazards of high surface temperature and should STAY AWAY to avoid burns or clothing i

Bottom of window(wider frame)Refi t and Check Window1. To refi t the window, place the window against the fi rebox’s opening frame. Make sure that the wi

OpenOpenCloseCloseNGFlashback shield (for LPG only)LPG Air Shutter SliderOpenCloseLPGNG Air Shutter Slider & CoverCheck OperationTurn the fi replac

Packing Contents:1 Wall Bracket A2 Screws B1 Screw C2 Wall Anchor D1 Spacer E (detach before assembly)1 Wall Bracket FSwitch PlateAlternative 1Alter

Optional Wall Switch Kit 1265WSKConnectorRedYellowGV60 Wiring DiagramWiring DiagramQUALIFIED INSTALLER33

Approved Venting ComponentsApproved Direct Vent Suppliers for Valor Models 700, 7393, 780, 785 and RF24DVVenting Parts Description Venting Parts Code

Warranty1. Extended Warranty CoverageFor a period of up to ten (10) years, Miles Industries Ltd., (the “Company”) or its appointed distributor will at

Code DescriptionPart Number1 Exhaust Slide Assembly 40011332 Exhaust Slide Gasket 40016623 Fan Closure Plate 40011364 Port Cover 40018205 Rock Support

Spare PartsCode DescriptionPart NumberRight Fluted Panel (739IR) 4001813Right Brick Panel (739JL) 400181068 Glass Panel (739IR) 400183669 Front Suppor

Spare PartsNGLPG182025212223241912345678910111213141516172627282930313233343536373839404245a, 45b14aNGLPG13a4748495051525349a7172737475767778445556575

Thank You ...For purchasing a Valor by Miles Industries. Your new radiant gas heater is a technical appliance that must be installed by a qualifi ed in

4Safety and Your FireplacePlease Follow These Important Child Safety Precautions and Recommendations,• Parts of your Valor Fireplace become extremely

Tape ShutThank you for choosing a Valor ProductPostageneededMiles Industries Ltd.190 - 2255 Dollarton HighwayNorth Vancouver, BC V7H 3B1 CanadaF

5Operating Your Fireplace for the First TimeWhen operating your new fi replace for the fi rst time, some vapors may be released due to the burning of cu

Bottom of window(wider frame)Owner’s InformationCleaning Your FireplaceImportant - Glass cleaning - Mineral depositsOne of the by-products of the comb

Owner’s Information6. If the Hot Glass Warning plate has been removed from the front lower corner of the window, reinstall it by sliding it between t

Owner’s InformationONOFFManual On/Off SwitchUsing Handset Wall HolderYour fi replace equipment includes a wall holder to store the handset. If it hasn’

Remote Control OperationWhen the pilot is off, it will take 2 minutes before it can be lit again.TO TURN ON APPLIANCE TO TURN OFF APPLIANCEFLAME HEIGH